Connector Description
Terminal Blocks Description
The terminal block signals are defined by placing extension X modules on the backside of the CHESTER mainboard. You can find more information in the Backside Modules chapter.
Terminal Block Solder Bridges
When there are no extension modules in slot A or B, the 8-pin terminal blocks can be configured using solder bridges.
Terminal block pins can have these signals based on solder bridges:
- Terminals A1-A8 and B1-B8 can be connected to the GND.
- Terminals A6, A3, B6, B3 can be connected to VDD
- Terminals A5, A2, B5, B2 can be connected to DQ (1-Wire Bus).
1-Wire extension
This picture shows how to extend the 1-Wire bus to 8-pin terminal blocks A and B. Solder the highlighted solder bridges so the 1-Wire signals from the 1-Wire terminal block are duplicated to the 8-pin terminal blocks.
Please note that the solder bridges are on the bottom side of the PCB. So in the picture below the blue solder bridge rectangles on the right of the PCB actually connects signals to the left 8-pin terminal blocks TB1 and TB2 when looked at the front of the PCB.
This picture shows the terminal blocks connection:
This table shows the connection of 1-Wire to terminal blocks and JST 8-pin connectors::
Terminal BLOCK Position | Signal Name | Signal Description |
---|---|---|
A1 or B1 | GND | System ground signal |
A2 or B2 | DQ | 1-Wire Data |
A3 or B3 | VDD | Power |
A4 or B4 | GND | System ground signal |
A5 or B5 | DQ | 1-Wire Data |
A6 or B6 | VDD | Power |
A7 or B7 | NC or GND | Not connected or GND |
A8 or B8 | NC or GND | Not connected or GND |
Backside Module
This section provides information on signal mapping for the two backside slots (A and B) on the CHESTER mainboard.
The backside slots use two rows of signals:
Top Row (closer to the antenna)
This signal row (with nine 2.54 mm distanced pins) provides power rails + digital signals with the signal definition in the table below.
Bottom Row (closer to the terminal blocks)
This signal row (with eight 2.54 mm distanced pins) directly connects to the terminal blocks, and their meaning is module-specific.
Top Row Signals (Slot A)
The following table lists the signals in the left-to-right order when you flip the board (slot A is on the right side).
Position | Signal Name | Signal Description | Connection on nRF52840 |
---|---|---|---|
1 | +V | System positive rail | - |
2 | GP3A | General purpose I/O | P0.31/AIN7 |
3 | GP2A | General purpose I/O | P0.02/AIN0 |
4 | GP1A | General purpose I/O | P0.29/AIN5 |
5 | GP0A | General purpose I/O | P0.03/AIN1 |
6 | SDA | System I²C bus (data) | - |
7 | SCL | System I²C bus (clock) | - |
8 | VDD | System VDD rail | - |
9 | GND | System ground signal | - |
Top Row Signals (Slot B)
The following table lists the signals in the left-to-right order when you flip the board (slot B is on the left side).
Position | Signal Name | Signal Description | Connection on nRF52840 |
---|---|---|---|
1 | +V | System positive rail | - |
2 | GP3B | General purpose I/O | P0.05/AIN3 |
3 | GP2B | General purpose I/O | P0.04/AIN2 |
4 | GP1B | General purpose I/O | P0.30/AIN6 |
5 | GP0B | General purpose I/O | P0.28/AIN4 |
6 | SDA | System I²C bus (data) | - |
7 | SCL | System I²C bus (clock) | - |
8 | VDD | System VDD rail | - |
9 | GND | System ground signal | - |